Florida rehab costs

Electrical panels and rewiring in older Florida houses

Electrical work is the line item with the widest spread on a Florida rehab estimate. A panel swap is a short job. A full rewire of a 1960s house is a different project with a different budget.

Planning range · typical single-family house$2,500 to $18,000

Two very different jobs under one line

A panel replacement swaps the breaker box, and often the meter can and service entrance, while keeping the existing branch wiring. It usually takes a day or two plus a utility disconnect and reconnect. A rewire replaces the branch circuits running through walls and attic. It means opening drywall, fishing new cable and patching afterward. The planning range on this page spans both, from the low end of a straight panel swap to the high end of a full rewire with a service upgrade.

Most investment houses land somewhere between. A common scope is a new panel and service, plus replacing specific problem circuits, adding grounding where outlets are two-prong, and bringing kitchen, bath, laundry and exterior outlets up to current protection rules. Prices vary by county, materials, permit requirements and electrician availability, and the age of the house matters more than its size. A house that was fully updated with permits in the last couple of decades may only need a panel and a few devices.

Panels and wiring Florida insurers flag

Any of these on a 4-point inspection can stop a policy from being written, and without a policy the next buyer’s lender will not close. That makes electrical one of the few rehab items where the market sets the requirement, not the investor. If a listing’s rehab estimate includes a panel line, assume the reason is on this list.

  • Federal Pacific Electric panels with Stab-Lok breakers, known for breakers that may fail to trip.
  • Zinsco and Sylvania-Zinsco panels, with bus bar and breaker problems documented over decades.
  • Challenger panels from certain production years, which many carriers treat the same way.
  • Fuse boxes still in service, which most carriers will not write.
  • Aluminum branch wiring from roughly the mid-1960s to the mid-1970s, unless remediated with approved connectors.
  • Cloth-insulated wiring and ungrounded circuits in the oldest housing stock.
  • Double-tapped breakers, missing knockouts and amateur additions visible when the dead front comes off.

Service upgrades and the utility

Moving from a 100-amp to a 200-amp service is common when you add a heat pump, an electric range, a tankless water heater or an EV charger, or when the old service is undersized for a modern house. That upgrade involves the local utility, whether that is a large investor-owned company or a municipal provider. The utility controls the disconnect and reconnect, and in some areas also the meter and service drop, so their schedule becomes part of yours.

Ask the electrician how long the utility usually takes in that territory, and schedule the work so the house is not without power during finish trades. Overhead service drops that are damaged or pulling away from the mast, and meter cans rusted by salt air, are usually caught at this stage and priced as add-ons. Underground service problems are less common but more expensive, so ask early if the house has a buried service.

What a permitted job triggers

Once an electrical permit is open, the inspector looks at more than the panel. Expect requirements for ground-fault protection in kitchens, bathrooms, garages, laundry areas and outdoors, arc-fault protection on many interior circuits, correct grounding and bonding, smoke alarms in the right places, and labeled circuits. None of that is gold-plating. It is what the current code asks for when the work is permitted, and it is cheaper to plan for than to discover at inspection.

Do not skip the permit to save time. An unpermitted panel shows up in the next buyer’s 4-point, which asks whether the panel looks original and whether there are signs of amateur work. Insurers and buyers both treat unpermitted electrical as a red flag. In most cases an LLC cannot pull an owner-builder electrical permit on a house it plans to sell or rent, so a licensed electrical contractor needs to pull it.

Funding electrical work through draws

On Think Off Market, the rehab estimate on each listing breaks electrical out as its own line so you can see what the lender sized. Think Private Lending funds the approved rehab budget in draws as work is completed and verified. Electrical often splits into two draws: rough work while walls are open, and finish work after drywall and fixtures. Ask your electrician to invoice in the same two stages so your paperwork matches the verification.

Rough electrical needs a passed rough inspection before drywall covers it. Photograph every open wall after that inspection passes. If a later trade damages something or a buyer asks about the work, those photos answer the question. The final draw for electrical usually follows the final inspection, along with installed fixtures, devices and cover plates.

Reading an electrician’s proposal

The proposal should state the panel brand, size in amps and breaker count, whether the meter can and mast are included, the number and type of circuits being replaced, how many outlets are being converted to grounded or GFCI-protected, and who patches drywall after a rewire. Patching is the line most often left out. If the electrician only cuts holes, you need a drywall crew, and that cost belongs in the electrical comparison. Verify the Florida electrical contractor license and ask for proof of insurance.

Ask one more question that separates careful electricians from fast ones: what happens if the inspector requires more than the bid covers. Older houses sometimes reveal buried junction boxes, undersized circuits feeding the AC or a bonding problem at the water heater. A good proposal lists likely add-ons with prices, so you can approve them in minutes instead of losing a week. Write those prices into the contract so the draw paperwork and the invoice match.

Straight answers

Questions investors ask

How much does it cost to replace a Federal Pacific panel in Florida?

A straight panel swap on an investment house often lands at the low end of the $2,500 to $18,000 range on this page. It climbs if the service needs upgrading, the meter can is corroded, or the inspector finds circuits that must be corrected.

Will insurers write a policy on a house with aluminum wiring?

Many will not unless the wiring has been remediated with approved connectors by a licensed electrician or replaced. Ask your agent before closing, since the answer changes by carrier.

Do I need a full rewire or just a new panel?

Most investment houses need a new panel plus targeted circuit work, not a full rewire. A full rewire is usually reserved for cloth wiring, widespread aluminum branch circuits or extensive amateur work. A licensed electrician walking the house is the only way to know.

See the addresses. Walk the houses. Close with the money already lined up.

Buyer access is free. Tell us what you buy and where, and we will open the full listings: addresses, photos, access instructions and the financing terms behind each one.