Pipe materials that trigger a repipe
Polybutylene and old galvanized steel are the two materials that most often force a repipe on a Florida investment house. Polybutylene is a gray or blue plastic supply line installed in many homes from the late 1970s into the mid-1990s. It tends to fail at fittings without warning, and many insurers will not write a policy while it is present. Galvanized steel shows up in older houses and corrodes from the inside, which shows up as low pressure, brown water and pinhole leaks.
A third group is less common but worth knowing: certain composite pipe systems from the late 1990s and 2000s that have had fitting failures, and houses where previous owners mixed materials during patch repairs. A plumber can usually identify supply material at the water heater, under sinks and at the main shutoff. If you see gray plastic with crimp rings, assume polybutylene until someone tells you otherwise.
Walk the house with the material question in mind before you sign the purchase contract. Look at the water heater connections, the lines under the kitchen sink and the hose bibs outside. Note any patched sections, because a house that has had several leak repairs is telling you the rest of the system is close behind. A short walk answers whether the rehab estimate needs a repipe line at all.
PEX or copper on a rental or flip
PEX is the default choice for repiping Florida investment houses. It costs less, installs faster, needs fewer fittings in walls, and handles the attic routing that slab-on-grade houses require. Copper still has a place in some high-end flips and in coastal areas where buyers expect it, but copper can suffer pinhole leaks in some water conditions, and the price difference is hard to justify on most rentals.
The bigger decision is routing. Most Florida houses sit on a slab, and supply lines in older homes often run under or through it. A repipe almost always abandons those lines and reroutes new pipe through the attic and down interior walls. That avoids breaking the slab but means opening drywall at each fixture. Ask the plumber how many openings to expect and whether patching and texture matching are in the bid.
What the cost covers and what it misses
Prices vary by county, materials, permit requirements and plumber availability. House layout matters too: a long single-story ranch with bathrooms at opposite ends needs more pipe than a compact house with back-to-back baths. Two-story houses cost more because routing through floors is harder. If the water heater is near the end of its life, replace it during the repipe, since the plumber is already there and the 4-point inspection will note its age.
- Included in most bids: new supply lines to every fixture, new shutoff valves, connection at the main and the water heater, and the plumbing permit.
- Often included: drywall cuts and rough patches at each access point.
- Often excluded: texture matching, paint, tile repair behind showers and replacing old fixtures that will not accept new connections.
- Usually excluded: the main line from the meter to the house, which may be a separate job if it is also old material.
- Not part of a repipe: drain lines, which are a separate and often larger problem in older houses.
Insurance, the 4-point and buyers
The plumbing section of a Florida 4-point inspection records supply line material, water heater age and location, and any active leaks or signs of past leaks. Polybutylene on that report is enough for many carriers to decline. A completed repipe with a passed final inspection solves the problem, and the permit record is your proof. Keep the permit number and the plumber’s invoice describing the material installed.
For a flip, the repipe is rarely something buyers notice as a feature, but its absence is something their inspector will notice. For a rental, the repipe reduces the risk of a slow leak inside a wall turning into a mold claim and a tenant problem. Either way, budget it early: the listing’s rehab estimate on Think Off Market shows whether the plumbing line was sized for a repipe or only for fixture work.
Sequencing the repipe and the draw
Schedule the repipe before drywall repair, paint and finish plumbing, and after any demolition that opens the walls anyway. If a kitchen or bathroom is being gutted, the plumber can run new lines with no extra cutting in those rooms. Think Private Lending funds the approved rehab budget in draws as work is completed and verified, and the repipe usually qualifies for a draw once the rough plumbing inspection passes and the system holds pressure.
Ask the plumber to pressure test with you or your project manager present, or to send a photo of the gauge at the start and end of the test. Then photograph every open wall before patching. That record supports your draw request and answers later questions from a buyer or insurer about what is behind the drywall.
Bid checks that save a repipe budget
The most common repipe overrun is not the plumbing. It is the finish work afterward, because a crew that cuts twenty openings and leaves rough patches hands you a drywall, texture and paint job you did not price. Ask each plumber for photos of a finished repipe on a similar house. If the patches look like the rest of the wall, their number is closer to the real cost than a lower bid that stops at the pipe.
- Confirm the pipe material, brand and fitting type are written into the bid.
- Count the fixtures the plumber priced and compare that count to the house.
- Ask whether drywall patching, texture and paint are included or excluded.
- Verify the plumber’s Florida license and current insurance before any deposit.
- Ask about the main line from the meter and price it separately if it is also old.