Repair or replace: the investor’s test
Replace the system when it is old, uses discontinued refrigerant, or needs a major component like a compressor or coil. Repair it when it is reasonably young and the problem is a capacitor, contactor, drain line or minor leak. That test sounds simple, but on a flip the bigger factor is the buyer. A buyer’s inspector will write up an old unit even if it cools today, and the buyer’s agent will use that line to renegotiate after you have already spent your rehab money.
Systems that still run on R-22 are the clearest replace case. That refrigerant is no longer produced, so recharging an old system costs more each year and a leak can end its life overnight. Newer equipment is also moving away from R-410A to lower-impact refrigerants, which means parts and charging practices are shifting. For a rental you plan to hold, a new system buys predictable years. For a flip, it removes a negotiation point.
Parts of the job that move the price
Prices vary by county, equipment brand, permit requirements and how many installers are available in your area during peak summer, so two quotes on the same house can land far apart for honest reasons. Ask each installer to break equipment, labor, ductwork and permit into separate numbers. That lets you compare the parts that really differ instead of comparing two totals that cover different work.
- Tonnage, which should come from a load calculation rather than from the size of the old unit.
- Straight AC with electric heat strip versus a heat pump, which is common across central and south Florida.
- Air handler location, since attic installs cost more in labor than a garage or closet swap.
- Line set replacement, which is often required when changing refrigerant types.
- New pad, disconnect, float switch, secondary drain pan and condensate line to meet current code.
- Coastal-rated or coated coils for houses close to salt air.
- Duct repairs or full duct replacement, quoted separately from the equipment.
Ductwork is where cheap installs fail
A new condenser on old ductwork is a common way to waste money on a Florida house. Flex duct in hot attics sags, separates at the boots and gets crushed by previous trades. Leaky return plenums pull attic air into the system, which adds humidity and can feed mold on supply registers. If the ducts are original to an older house, ask the installer to inspect them in person and price repairs or replacement as a separate line you can keep or drop.
Oversizing is the other quiet problem. An oversized system cools the air fast but shuts off before it removes enough moisture, so the house feels clammy and grows mildew in closets. Many building departments now ask for a load calculation with the permit, and a good installer runs one anyway. On a rental, a correctly sized system keeps tenants comfortable and reduces service calls about musty smells that turn into moisture complaints.
What the 4-point and buyers want to see
The 4-point inspection that Florida insurers require on older homes records the HVAC system’s age, condition and whether it is working. A new system with a permit and a data plate showing the install date answers that question cleanly. Buyers want the same thing in a different form: the install date, the manufacturer warranty registration and a receipt. Register the equipment warranty right after install, because many manufacturers shorten coverage if registration is late.
Keep a one-page folder for the house with the permit number, final inspection result, equipment model and serial numbers, and warranty registration confirmation. Hand it to the listing agent at sale or to your property manager at lease-up. It costs nothing to assemble and it closes questions that otherwise stall a deal. Appraisers rarely add much value for a new AC, but a dead AC can make a house unfinanceable for the next buyer.
Timing the install inside your draw schedule
Install HVAC after rough electrical and after any duct-related drywall or ceiling work, but early enough that the house can be cooled while finishes go in. Running fans and dehumidifiers through a Florida summer while flooring and paint cure is expensive and can damage new materials. On Think Off Market listings, HVAC usually appears as its own rehab line, and Think Private Lending releases that money in a draw once the system is installed, the permit is finaled and the work is verified.
Florida requires a Notice of Commencement for many improvements, but the threshold for HVAC repair or replacement is higher than for general work, so a single-system swap often falls below it. Your installer and the building department will tell you which applies. Either way, the permit itself is not optional, and an unpermitted swap shows up later when an insurer, buyer or appraiser asks for the install record.
Comparing two HVAC quotes fairly
Put the quotes side by side on the same items: brand and model numbers for both the outdoor and indoor units, tonnage, efficiency rating, refrigerant type, line set, duct scope, thermostat, permit, removal of the old unit and warranty length on parts and labor. Check the contractor’s Florida mechanical or air conditioning license on the state site. A quote that only lists a tonnage and a total is not a quote, it is a placeholder for a later change order.
Also ask what happens if the installer finds a problem after the old unit comes out, such as a rusted air handler platform, a failed secondary drain pan or a corroded electrical disconnect. A good contractor names those possibilities up front and prices them as conditional items. That keeps the number on your rehab estimate honest and keeps your draw request from stalling while you argue over a surprise invoice.